Servo Voltage Stabilizer

Approx. Rs 4,25,000 / PieceGet Latest Price

Features:

• Less maintenance
• Input voltage balance
• Load balance at any power factor

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 12,50,000 / PieceGet Latest Price

• Higher current produces higher losses in electrical motors which cause premature failure of winding.
• These higher losses of electric motors also increase the losses of cables, switches, transformers and others associated equipment.
• For smooth continuous operation of motors, overhead relays are usually set at 20% higher setting.

• The line current increases by 1.5 times.
• If the relay setting is at 15-20% higher than actual operating current than the relay will take 4-6 minutes to travel.
• The motor (particularly smaller capacity motors up to 7.5 H.P) cannot withstand this high current for such a long time and in most of the cases it burns out before the relay trips.
• Heavy short circuit current flows through the relays, contactors, cables, etc.
• Under this condition, the relay and contactor trips produce sparks and sometimes it also bursts.
• This further damages the switchgear and in some of the cases may cause fire also.

• Price May be varry according to the client specifictions.

Approx. Rs 1,50,000 / PieceGet Latest Price

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 6,50,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Approx. Rs 26,50,000 / PieceGet Latest Price

• Jindal's rectifiers equipments are wound with electrolytic Prime grade italics to minimise power losses, in comparison to Aluminium italic conductor used by many other manufactures. Our equipments are designed liberally as per capacity and are ideally suitable for marginal overloading conditions.
• We use vertical Rolling contact type voltage regulator wound with heavy section of copper strips suitable for 100% continuous duty cycle for industrial applications, in comparison to conventional wire wound Regulator used by other manufacturers. The carbon rollers move on both sides of the winding.
• DIODE : Silicon diodes are tested in house, similar PIV batch and same forward drop diodes are used in the equipment for equal load sharing and reducing the power losses of diodes.
• We use imported CRGO Lamination core which have minimum power losses and results in better efficiency of equipment and saving in energy bill.
• Epoxy paint is used which is resistant to acidic environment of plating process and enhance the life of the equipment by preventing it from
• We use reputed make AE/RISHABH make DC motor only which are very accurate and durable.
• Jindal have maintained enviable reputation in market in after sales service. This fact can be verified from any of our customers.

• Price May be vary according to the client specifications.

Approx. Rs 8,25,000 / PieceGet Latest Price

Industrial Robot

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 8,50,000 / PieceGet Latest Price

Industrial Robot

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 6,50,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Approx. Rs 22,25,000 / PieceGet Latest Price

Industrial Robot

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Approx. Rs 4,15,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Approx. Rs 10,00,000 / PieceGet Latest Price

Industrial Robot

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 5,50,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 20,25,000 / PieceGet Latest Price

• Jindal's rectifiers equipments are wound with electrolytic Prime grade italics to minimise power losses, in comparison to Aluminium italic conductor used by many other manufactures. Our equipments are designed liberally as per capacity and are ideally suitable for marginal overloading conditions.
• We use vertical Rolling contact type voltage regulator wound with heavy section of copper strips suitable for 100% continuous duty cycle for industrial applications, in comparison to conventional wire wound Regulator used by other manufacturers. The carbon rollers move on both sides of the winding.
• DIODE : Silicon diodes are tested in house, similar PIV batch and same forward drop diodes are used in the equipment for equal load sharing and reducing the power losses of diodes.
• We use imported CRGO Lamination core which have minimum power losses and results in better efficiency of equipment and saving in energy bill.
• Epoxy paint is used which is resistant to acidic environment of plating process and enhance the life of the equipment by preventing it from
• We use reputed make AE/RISHABH make DC motor only which are very accurate and durable.
• Jindal have maintained enviable reputation in market in after sales service. This fact can be verified from any of our customers.

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 15,25,000 / PieceGet Latest Price

Industrial Robot

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 4,25,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 2,25,000 / PieceGet Latest Price

• Higher current produces highest losses in electric motor which causes premature failure winding.
• These higher losses of electric motors also increase the losses of cables, switches, transformers and other associated equipment.
• For smooth continuous operation of motors, overload relays are usually set at 20% higher setting.

• Price May be vary according to the client specifications.

Approx. Rs 4,25,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 6,50,000 / PieceGet Latest Price

• Jindal's rectifiers equipments are wound with electrolytic Prime grade italics to minimise power losses, in comparison to Aluminium italic conductor used by many other manufactures. Our equipments are designed liberally as per capacity and are ideally suitable for marginal overloading conditions.
• We use vertical Rolling contact type voltage regulator wound with heavy section of copper strips suitable for 100% continuous duty cycle for industrial applications, in comparison to conventional wire wound Regulator used by other manufacturers. The carbon rollers move on both sides of the winding.
• DIODE : Silicon diodes are tested in house, similar PIV batch and same forward drop diodes are used in the equipment for equal load sharing and reducing the power losses of diodes.
• We use imported CRGO Lamination core which have minimum power losses and results in better efficiency of equipment and saving in energy bill.
• Epoxy paint is used which is resistant to acidic environment of plating process and enhance the life of the equipment by preventing it from
• We use reputed make AE/RISHABH make DC motor only which are very accurate and durable.
• Jindal have maintained enviable reputation in market in after sales service. This fact can be verified from any of our customers.

• Price May be vary according to the client specifications.

Approx. Rs 21,25,000 / PieceGet Latest Price

• Jindal's rectifiers equipments are wound with electrolytic Prime grade italics to minimise power losses, in comparison to Aluminium italic conductor used by many other manufactures. Our equipments are designed liberally as per capacity and are ideally suitable for marginal overloading conditions.
• We use vertical Rolling contact type voltage regulator wound with heavy section of copper strips suitable for 100% continuous duty cycle for industrial applications, in comparison to conventional wire wound Regulator used by other manufacturers. The carbon rollers move on both sides of the winding.
• DIODE : Silicon diodes are tested in house, similar PIV batch and same forward drop diodes are used in the equipment for equal load sharing and reducing the power losses of diodes.
• We use imported CRGO Lamination core which have minimum power losses and results in better efficiency of equipment and saving in energy bill.
• Epoxy paint is used which is resistant to acidic environment of plating process and enhance the life of the equipment by preventing it from
• We use reputed make AE/RISHABH make DC motor only which are very accurate and durable.
• Jindal have maintained enviable reputation in market in after sales service. This fact can be verified from any of our customers.

• Price May be vary according to the client specifications.

Approx. Rs 2,50,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Approx. Rs 2,75,000 / PieceGet Latest Price

• Higher current produces highest losses in electric motor which causes premature failure winding.
• These higher losses of electric motors also increase the losses of cables, switches, transformers and other associated equipment.
• For smooth continuous operation of motors, overload relays are usually set at 20% higher setting.

• Price May be vary according to the client specifications.

Approx. Rs 2,10,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.

Approx. Rs 28,75,000 / PieceGet Latest Price

• Jindal's rectifiers equipments are wound with electrolytic Prime grade italics to minimise power losses, in comparison to Aluminium italic conductor used by many other manufactures. Our equipments are designed liberally as per capacity and are ideally suitable for marginal overloading conditions.
• We use vertical Rolling contact type voltage regulator wound with heavy section of copper strips suitable for 100% continuous duty cycle for industrial applications, in comparison to conventional wire wound Regulator used by other manufacturers. The carbon rollers move on both sides of the winding.
• DIODE : Silicon diodes are tested in house, similar PIV batch and same forward drop diodes are used in the equipment for equal load sharing and reducing the power losses of diodes.
• We use imported CRGO Lamination core which have minimum power losses and results in better efficiency of equipment and saving in energy bill.
• Epoxy paint is used which is resistant to acidic environment of plating process and enhance the life of the equipment by preventing it from
• We use reputed make AE/RISHABH make DC motor only which are very accurate and durable.
• Jindal have maintained enviable reputation in market in after sales service. This fact can be verified from any of our customers.

• Price May be vary according to the client specifications.

Approx. Rs 35,00,000 / PieceGet Latest Price

• Jindal's rectifiers equipments are wound with electrolytic Prime grade italics to minimise power losses, in comparison to Aluminium italic conductor used by many other manufactures. Our equipments are designed liberally as per capacity and are ideally suitable for marginal overloading conditions.
• We use vertical Rolling contact type voltage regulator wound with heavy section of copper strips suitable for 100% continuous duty cycle for industrial applications, in comparison to conventional wire wound Regulator used by other manufacturers. The carbon rollers move on both sides of the winding.
• DIODE : Silicon diodes are tested in house, similar PIV batch and same forward drop diodes are used in the equipment for equal load sharing and reducing the power losses of diodes.
• We use imported CRGO Lamination core which have minimum power losses and results in better efficiency of equipment and saving in energy bill.
• Epoxy paint is used which is resistant to acidic environment of plating process and enhance the life of the equipment by preventing it from
• We use reputed make AE/RISHABH make DC motor only which are very accurate and durable.
• Jindal have maintained enviable reputation in market in after sales service. This fact can be verified from any of our customers.

• Price May be vary according to the client specifications.

Approx. Rs 2,75,000 / PieceGet Latest Price

• It is a equipment, which pays back its cost within 1-2 years. If we try to rectify voltage variation manually it might be rectified but cannot be monitor always.
• Improvement in power factor and reduction in MDI
• Uniform quality of end product
• Better efficiency in plants due to less Breakdown
• Depreciation @40% as per Income Tax Act
• The Above advantages have been confirmed by the customers by placing repeat orders for their expansion of Plants.

• Price May be vary according to the client specifications.

Additional Information:

Approx. Rs 3,50,000 / PieceGet Latest Price

• Three Phase Automatic Voltage Controller Stabilizer is an industrial robot which first monitor items rectifier the voltage variation round the clock & whenever there is any voltage fluctuations, it rectifiers to the desired level in few seconds.
• The Basic purpose of AVC is to maintain the desired voltage and to reduce the breakdown of electrical equipments due to low/high voltage. Power saving Reduction in MDI and improvement of P.F. will be added advantages at high voltage.

Capital & Interest cost is just 1.5% per month.

• Saving by reduction in breakdown of electrical equipment and energy saving shall be 4-8 times of capital & interest cost. Voltage variation is common phenomenon. The input voltage is generally low during day time and high during night hours.
• Apart from above, few months in a year/few days in a month/few hours in a day the voltage is either low or high due to the following reasons:
• Holidays
• Peak Hours
• Rain Days
• Agricultural Load
• Weather Conditions etc.

Note:-

• Price May be vary according to the client specifications.

Approx. Rs 4,00,000 / PieceGet Latest Price

• Price May be vary according to the client specifications.